ECU and Throttle re learn how to. - Skyline Owners Forum

Welcome to the SkylineOwners.Com website. We aim to provide you with the largest knowledgebase anywhere on the internet for the Nissan Skyline.


Go Back   Skyline Owners Forum > G35/350GT Forum > General 350/g35


Reply
 
LinkBack Thread Tools Rate Thread
Old 30-10-2015, 04:10 PM   #1
Super Moderator
 
Tricky-Ricky's Avatar
 
Drives: Skyline 350GT 6 speed
Join Date: Oct 2005
Location: Norfolk
Posts: 8,931
Club ID#: 5836


Trade Feedback: (1)


View My Pictures
ECU and Throttle re learn how to.

This guide is actually for the 350Z, but as its basically the same it should work fine for the 350GT. (let me know if anything doesn't work)
BUT REMEMBER THE TIMING IS CRITICAL!

ECU Resetting Procedures

Please read all instructions and be familiar with them before any attempts.
A stop watch or an analog clock with a second?s needle will be useful.

ECU Resetting Procedures

Timing is extremely critical. If it is NOT DONE within the specify time, the ECU will not reset and the Check Engine Light (CEL) will continue to remain ON.
A stop watch or an analog clock with a second?s needle will be useful.

Operations Procedures

1. Confirm that accelerator pedal is fully released, turn ignition switch ?ON? and wait 3 seconds.
2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.
2a. Fully depress the accelerator pedal (HARD).
2b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
4. Fully release the accelerator pedal (while the CEL is still blinking)
5. Wait about 10 second.
6. Fully depress the accelerator pedal and keep it for more than 10 seconds.
7. Fully release the accelerator pedal (The CEL light will continue to blink).
8. Turn ignition switch to ?OFF? position and now you can start the car. The CEL light should be gone.

If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to resetting the ECU.


Accelerator Pedal Release Position Learning

Operation Procedure
1. Make sure that the accelerator pedal is fully released.
2. Turn ignition switch ?ON? and wait at least 2 seconds.
3. Turn ignition switch ?OFF? wait at least 10 seconds.
4. Turn ignition switch ?ON? and wait at least 2 seconds.
5. Turn ignition switch ?OFF? wait at least 10 seconds.


Throttle Valve Closed Position Learning

Operation Procedures
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch is ?ON?.
3. Turn ignition switch is ?OFF? wait at least 10 seconds.
Make sure that the throttle valve moves during above 10 seconds by confirming the operating sound.


Idle Air Volume Learning (Throttle Position Learning)
It is better to count the time accurately with a clock.

Operation Procedures
1. Perform ?Accelerator Pedal Released Position Learning?.
2. Perform ?Throttle Valve Closed Position Learning?.
3. Start engine and warm it up to normal operating temperature.
4. Turn ignition switch ?OFF? and wait at least 10 seconds.
5. Conform that accelerator pedal is fully released, turn ignition switch ?ON? and wait 3 seconds.
6. Repeat the following (steps 7a, 7b) procedures quickly five times within 5 seconds.
7a. Fully depress the accelerator pedal (HARD)
7b. Fully release the accelerator pedal.
8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the Check Engine Light (CEL) stops blinking and turned ON.
9. Fully release the accelerator pedal within 3 seconds after the CEL is ON.
10. Start engine and let it idle.
11. Wait 20 seconds.
12. Rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications.
__________________
Pedants are men who would appear to be learned, without the necessary ingredient of knowledge.
- George Bancroft

Originally posted The Great White

"Nissan is like Lego"
Tricky-Ricky is offline   Reply With Quote Share on facebook
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT +1. The time now is 06:44 AM.


Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.1
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©2002 - 2019, Verticalscope Inc.